Elmea

CUTTING UNITS

WHY CHOOSE AN ELMEA CUTTING UNIT?
  • Simplicity: compact machinery to set up near the press without any need for coupling or tuning
  • Convenience: the body of the cutting unit is equipped with a base with manual lift+/- 50 mm to align the cutting opening to the tape passage height
  • Speed: possibility of cutting multiple tapes simultaneously
  • Long lasting: little maintenance, components subject to wear last over time
  • Reliability: Solid and long lasting machinery, robust structure in electro-welded steel
UT 29 MODEL
UT 30 MODEL
UT 43 MODEL
UT 51 MODEL
UT 29 Model

CHARACTERISTICS OF THE CUTTING UNIT MODEL UT 29:

  • tape width 200 mm
  • Cutting sections: Cutting section 200 x 2 / 150 x 2.5 / 100 x 3 / 50 x 4
  • Cuts per minute 40
  • Four-edged blade in the best, prestigious K110 steel or in K390 steel also suitable for cutting sheet metal in silicon and stainless steel
  • Adjustable and resharpening blades, therefore long lasting
  • Possibility of cutting synchronism with other operating machines (presses, feeders, etc.) using a mechanical connection device with electro-pneumatic control
  • Cutting possible using programmer to allow particular cutting sequences
  • Gearmotor with drive units in oil bath
  • Compact dimensions
  • With safety casing
  • Electrical system on machine with control using keypad and emergency button
UT 30 Model

CHARACTERISTICS OF THE CUTTING UNIT MODEL UT 30:

  • tape width 300 mm
  • Cutting sections: Cutting section 300 x 2 / 200 x 2.5 / 150 x 3 / 100 x 4
  • Cuts per minute 35
  • Four-edged blade in the best, prestigious K110 steel or in K390 steel also suitable for cutting sheet metal in silicon and stainless steel
  • Adjustable and resharpening blades, therefore long lasting
  • Possibility of cutting synchronism with other operating machines (presses, feeders, etc.) using a mechanical connection device with electro-pneumatic control
  • Cutting possible using programmer to allow particular cutting sequences
  • Gearmotor with drive units in oil bath
  • Compact dimensions
  • With safety casing
  • Electrical system on machine with control using keypad and emergency button
UT 43 Model

CHARACTERISTICS OF THE CUTTING UNIT MODEL UT 43:

  • tape width 500 mm
  • Cutting sections: Cutting section 500 x 2 / 300 x 2.5 / 250 x 3 / 150 x 4
  • Cuts per minute 35
  • Four-edged blade in the best, prestigious K110 steel or in K390 steel also suitable for cutting sheet metal in silicon and stainless steel
  • Adjustable and resharpening blades, therefore long lasting
  • Possibility of cutting synchronism with other operating machines (presses, feeders, etc.) using a mechanical connection device with electro-pneumatic control
  • Cutting possible using programmer to allow particular cutting sequences
  • Gearmotor with drive units in oil bath
  • Compact dimensions
  • With safety casing
  • Electrical system on machine with control using keypad and emergency button
UT 51 Model

CHARACTERISTICS OF THE CUTTING UNIT MODEL UT 51:

  • tape width 800 mm
  • Cutting sections: Cutting section 800 x 2 / 500 x 2.5 / 400 x 3 / 250 x 4
  • Cuts per minute 30
  • Four-edged blade in the best, prestigious K110 steel or in K390 steel also suitable for cutting sheet metal in silicon and stainless steel
  • Adjustable and resharpening blades, therefore long lasting
  • Possibility of cutting synchronism with other operating machines (presses, feeders, etc.) using a mechanical connection device with electro-pneumatic control
  • Cutting possible using programmer to allow particular cutting sequences
  • Gearmotor with drive units in oil bath
  • Compact dimensions
  • With safety casing
  • Electrical system on machine with control using keypad and emergency button